Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
31
Installation and Upgrades / Re: Can't access from outside
« on: May 30, 2011, 04:38:18 pm »
uhh... nope, my router is ok... It gives access to my window$ server 2003 :/
and i've changed that rules.
It's in portugues BR, so, where's "Qualquer", read "Any".
and i've changed that rules.
It's in portugues BR, so, where's "Qualquer", read "Any".
32
Installation and Upgrades / Can't access from outside
« on: May 30, 2011, 03:45:21 pm »
Hey guys..
well, i can't access my zentyal gateway from outside. Well, i tryed to change that firewall rules, did "accept" to all incoming protocols i need (ssh, ftp) from any ip to any ip... and nothing happens. This is my second fresh install, and still no access.
well, i can't access my zentyal gateway from outside. Well, i tryed to change that firewall rules, did "accept" to all incoming protocols i need (ssh, ftp) from any ip to any ip... and nothing happens. This is my second fresh install, and still no access.
33
Installation and Upgrades / LDAP Error... Plz Help!
« on: May 13, 2011, 09:17:07 pm »
Hi guys,
Well, i had to re-install all my modules... so i did "sudo apt-get remove --purge ebox-*"
Then, "sudo apt-get install ebox-all"
but now, when i try to enable some modules, i get the error:
Failed to enable: root command /etc/init.d/slapd start failed. Error output: Command output: Starting OpenLDAP: slapd - failed. The operation failed but no output was produced. For hints on what went wrong please refer to the system's logfiles (e.g. /var/log/syslog) or try running the daemon in Debug mode like via "slapd -d 16383" (warning: this will create copious output). Below, you can find the command line options used by this script to run slapd. Do not forget to specify those options if you want to look to debugging output: slapd -h 'ldap:/// ldapi:/// ldaps:///' -g openldap -u openldap -F /etc/ldap/slapd.d/ . Exit value: 1
What can i do please?
Best regards
Well, i had to re-install all my modules... so i did "sudo apt-get remove --purge ebox-*"
Then, "sudo apt-get install ebox-all"
but now, when i try to enable some modules, i get the error:
Failed to enable: root command /etc/init.d/slapd start failed. Error output: Command output: Starting OpenLDAP: slapd - failed. The operation failed but no output was produced. For hints on what went wrong please refer to the system's logfiles (e.g. /var/log/syslog) or try running the daemon in Debug mode like via "slapd -d 16383" (warning: this will create copious output). Below, you can find the command line options used by this script to run slapd. Do not forget to specify those options if you want to look to debugging output: slapd -h 'ldap:/// ldapi:/// ldaps:///' -g openldap -u openldap -F /etc/ldap/slapd.d/ . Exit value: 1
What can i do please?
Best regards
34
Installation and Upgrades / Re: Can't enable DHCP
« on: June 01, 2010, 10:51:43 pm »
I found the problem. When i start the module, it cleans my /etc/default/dhcp3-server config.
I've removed the module and installed dhcp3-server mannualy and configured it.. it's working now, i think... At least until the next restart.
I've removed the module and installed dhcp3-server mannualy and configured it.. it's working now, i think... At least until the next restart.
35
Installation and Upgrades / Can't enable DHCP
« on: June 01, 2010, 09:16:29 pm »
Hi guys,
Well, i've changed my ethernet adapter, so it reconised the new one as "eth0_rename"
And so i can't start my DHCP server. Everything else is working well.
I've already tried to remove --purge ebox-dhcp, and install again, but no luck.
Does anyone know how can i fix it?
Well, i've changed my ethernet adapter, so it reconised the new one as "eth0_rename"
And so i can't start my DHCP server. Everything else is working well.
I've already tried to remove --purge ebox-dhcp, and install again, but no luck.
Does anyone know how can i fix it?
36
Installation and Upgrades / Slow Webserver
« on: May 26, 2010, 06:13:42 pm »
Hi guys,
I've installed Ebox 1.4, and it's running so smoothly. But sometimes, afeter some hours, web navigation begins to be slow. Does anyone knows what it could be?
I think that it may be a dns problem...
Thanks in advance.
I've installed Ebox 1.4, and it's running so smoothly. But sometimes, afeter some hours, web navigation begins to be slow. Does anyone knows what it could be?
I think that it may be a dns problem...
Thanks in advance.
37
Installation and Upgrades / Can't start printer server, proxy server or file server and no option for mail.
« on: May 20, 2010, 09:30:00 pm »
Hi guys,
I'm amazed with your truly good job with this project.
I'm using ubuntu server 10.04 (lucid) and i've done like i read on the tutorial, and it was installed correctly.
My only problem is that some modules are disabled and i can't enable it. I can't check the module.
I'm amazed with your truly good job with this project.
I'm using ubuntu server 10.04 (lucid) and i've done like i read on the tutorial, and it was installed correctly.
My only problem is that some modules are disabled and i can't enable it. I can't check the module.