Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
1
Installation and Upgrades / Re: SAMBA Error
« on: October 01, 2013, 10:12:07 pm »
@rpro disabling samba module will not loose your shares
2
Installation and Upgrades / Re: SAMBA Error
« on: October 01, 2013, 07:18:47 pm »
thanks @paulreynand for your help!!!....
I'm making my tests in an old PC before installation to a real server. So i was thinking there must be a problem about the delay that some process have to respond and some zentyal scripts and their time limits (there may other issues too).... i have installed zentyal 3.2 32bits several times and must of the times just a recent install, samba was doing what is suppost to do, but i have noticed in some installations that after clamav db get updated, it starts to show errors on samba changes.... i have been using top and i've been watching that clamav uses a lot of memory ( a lot for my old PC with 896MB in RAM) and noticed that swap was growing very fast. As my hards disks are slow (2 old 40GB IDE) i started to think... why just reapplied several times the changes in samba so all theses procedures will be cached in RAM next time i'll try to apply. So far by now is working. So my workaround is:
Notes: i'm having my two old 40GB hard disk on a linux kernel raid0 to try to gain some performance and i still need to repplied changes several times in samba must of time to get it done. BTW, guest access on shared folders have never worked for me don't allow any user to access
.
I'm making my tests in an old PC before installation to a real server. So i was thinking there must be a problem about the delay that some process have to respond and some zentyal scripts and their time limits (there may other issues too).... i have installed zentyal 3.2 32bits several times and must of the times just a recent install, samba was doing what is suppost to do, but i have noticed in some installations that after clamav db get updated, it starts to show errors on samba changes.... i have been using top and i've been watching that clamav uses a lot of memory ( a lot for my old PC with 896MB in RAM) and noticed that swap was growing very fast. As my hards disks are slow (2 old 40GB IDE) i started to think... why just reapplied several times the changes in samba so all theses procedures will be cached in RAM next time i'll try to apply. So far by now is working. So my workaround is:
- If you have installed zentyal on an old slow machine with less than 1.5Gb RAM
- Reapplied several times samba changes until you get no error (at least 3 times in my case). I usually tick & untick guest access on any share to reapply changes
Notes: i'm having my two old 40GB hard disk on a linux kernel raid0 to try to gain some performance and i still need to repplied changes several times in samba must of time to get it done. BTW, guest access on shared folders have never worked for me don't allow any user to access
.
3
Installation and Upgrades / Re: SAMBA Error
« on: September 27, 2013, 05:24:07 pm »
everybody please determine if you are using 32bits or 64bits distribution?
4
News and Announcements / Re: Zentyal 3.2 available!
« on: September 26, 2013, 01:01:59 am »3.2 Fresh install and samba do not work... this release is not good.
I'm having problems with samba too!!!
My ingredients:
- Zentyal 3.2 32bits ISO
- HP Compaq d530 CMT
- 40GB HD
- 1GB RAM
It seems that after clamav gets udpated zentyal samba scripts starts to working unstable.
This samba issue is not an impression.... it is fact!
maybe on 64bit release there's not that issue.
5
Installation and Upgrades / Re: SAMBA Error
« on: September 25, 2013, 08:25:02 am »
ok i just made a clean installation, everything was ok.... but after zentyal updates was done (even after restarting) is when come out the error:
The following modules failed while saving their changes, their state is unknown: samba
and stop to set up right permissions in /home/samba/shares folder....
why testing updates in a stable release? what are you thinking?
just stay away from updates
The following modules failed while saving their changes, their state is unknown: samba
and stop to set up right permissions in /home/samba/shares folder....
why testing updates in a stable release? what are you thinking?
just stay away from updates
6
Installation and Upgrades / Re: SAMBA Error
« on: September 25, 2013, 06:23:44 am »
i'm having troubles with samba too, i have made a new installation on an old PC for testing... i share a directory but it does not let me write even if told zentyal via web interface to do so. It does not change owner and folder Permissions on /home/samba/shares/shared_folder you have to do it manually 
7
News and Announcements / Re: Zentyal 3.2 available!
« on: September 20, 2013, 09:19:35 pm »
i have just downloaded Zentyal 3.2 ISO 32bits, just check the filenames in the screenshot i've attached!!!
Pages: [1]