Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
31
Installation and Upgrades / Re: Change the LDAP dc hostname and domainname
« on: January 23, 2012, 10:28:13 pm »
@majestyx Thank you very much for that 
32
Installation and Upgrades / Re: Jabber IM setup
« on: January 23, 2012, 07:41:55 pm »
Same here, Zentyal isntalled with 2.2.0, Jabber accessible and OK.
Double check the port is open in the firewall or explicitly open it?
And authorize the users ofcourse
Double check the port is open in the firewall or explicitly open it?
And authorize the users ofcourse
33
Installation and Upgrades / Re: Change the LDAP dc hostname and domainname
« on: January 21, 2012, 02:20:19 pm »
Just a kick 
is this really not possible to change?
is this really not possible to change?
34
Installation and Upgrades / Change the LDAP dc hostname and domainname
« on: January 17, 2012, 12:09:54 am »
After installing I found out my LDAP dc settings used were the DHCP local domain settings in my router (linked to the Eth0 external nic).
But the server is going to be placed elsewhere where the use of 'domainname' is not really nice to see.
How can I alter this value after the server has been build? And is there any way to avoid this in the future at install?
thx
But the server is going to be placed elsewhere where the use of 'domainname' is not really nice to see.
How can I alter this value after the server has been build? And is there any way to avoid this in the future at install?
Code: [Select]
LDAP information
Base DN: dc=servername,dc=domainname,dc=nl
Root DN: cn=ebox,dc=servername,dc=domainname,dc=nl
Users DN: ou=Users,dc=servername,dc=domainname,dc=nl
Groups DN: ou=Groups,dc=servername,dc=domainname,dc=nl
thx
35
Installation and Upgrades / Re: VPN Connection to Zentyal cloud fails on 2.2
« on: January 10, 2012, 11:33:54 pm »
May thanks sixstone, I thought I was loosing it. I cannot remember putting any illegal chars into those fields, but OK another case fixed.
Thanks again.
Thanks again.
36
Installation and Upgrades / Re: VPN Connection to Zentyal cloud fails on 2.2
« on: January 10, 2012, 03:14:08 pm »My best guess is that your credentials fail.
Can you log in Zentyal Cloud webinterface? YES I can
Can you unsubscribe and resubscribe? YES I did, this goes OK but then does not keep the VPN up.
What happens then? The same errors.
Jorge advised to install NTP to be sure the time was right, so I did and rebooted. as well. No result.
FYI: the cloud server nr is 72690.
37
Installation and Upgrades / [solved] VPN Connection to Zentyal cloud fails on 2.2
« on: January 10, 2012, 10:05:21 am »
Although subscribing to the zentyal cloud can be done OK, I cannot get it online.
In the dashboard it states that the VPN failed and the log tells more. The machine is a install of zentyal 2.2 with filesharing and the cloud client. All updates of modules and system applied.
I already tried removing all modules, rebooting and reinstalling them. What to try ?
In the dashboard it states that the VPN failed and the log tells more. The machine is a install of zentyal 2.2 with filesharing and the cloud client. All updates of modules and system applied.
I already tried removing all modules, rebooting and reinstalling them. What to try ?
Quote
Tue Jan 10 09:57:41 2012 OpenVPN 2.1.0 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 20 2010
Tue Jan 10 09:57:41 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info.
Tue Jan 10 09:57:41 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables
Tue Jan 10 09:57:41 2012 WARNING: file '/etc/openvpn/R_D_SRVS_5ac349a8d.conf.d/certificateKey' is group or others accessible
Tue Jan 10 09:57:41 2012 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted>
Tue Jan 10 09:57:42 2012 LZO compression initialized
Tue Jan 10 09:57:42 2012 Control Channel MTU parms [ L:1576 D:140 EF:40 EB:0 ET:0 EL:0 ]
Tue Jan 10 09:57:42 2012 Data Channel MTU parms [ L:1576 D:1450 EF:44 EB:135 ET:32 EL:0 AF:3/1 ]
Tue Jan 10 09:57:42 2012 Local Options hash (VER=V4): '31fdf004'
Tue Jan 10 09:57:42 2012 Expected Remote Options hash (VER=V4): '3e6d1056'
Tue Jan 10 09:57:42 2012 Attempting to establish TCP connection with [AF_INET]92.243.6.103:443 [nonblock]
Tue Jan 10 09:57:43 2012 TCP connection established with [AF_INET]92.243.6.103:443
Tue Jan 10 09:57:43 2012 Socket Buffers: R=[87380->131072] S=[16384->131072]
Tue Jan 10 09:57:43 2012 TCPv4_CLIENT link local: [undef]
Tue Jan 10 09:57:43 2012 TCPv4_CLIENT link remote: [AF_INET]92.243.6.103:443
Tue Jan 10 09:57:43 2012 TLS: Initial packet from [AF_INET]92.243.6.103:443, sid=5dd88df2 47083951
Tue Jan 10 09:57:43 2012 VERIFY OK: depth=1, /C=ES/ST=Nation/L=Nowhere/O=ebox-controlcenter.com/CN=Certification_Authority_Certificate
Tue Jan 10 09:57:43 2012 VERIFY OK: depth=0, /C=ES/ST=Nation/L=Nowhere/O=ebox-controlcenter.com/CN=vpn3.cloud.zentyal.com
Tue Jan 10 09:57:44 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key
Tue Jan 10 09:57:44 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Tue Jan 10 09:57:44 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key
Tue Jan 10 09:57:44 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication
Tue Jan 10 09:57:44 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA
Tue Jan 10 09:57:44 2012 [vpn3.cloud.zentyal.com] Peer Connection Initiated with [AF_INET]92.243.6.103:443
Tue Jan 10 09:57:46 2012 SENT CONTROL [vpn3.cloud.zentyal.com]: 'PUSH_REQUEST' (status=1)
Tue Jan 10 09:57:46 2012 AUTH: Received AUTH_FAILED control message
Tue Jan 10 09:57:46 2012 TCP/UDP: Closing socket
Tue Jan 10 09:57:46 2012 SIGTERM[soft,auth-failure] received, process exiting
38
Installation and Upgrades / DNS server assigned by DHCP not replaced in new environment
« on: January 05, 2012, 10:07:29 pm »
I installed the server (zentyal 2.2) with a single NIC in a small network.1 that supplies IP's via DHCP. The server gets an IP OK and sets up the default gateway OK as well. The DNS entry under network also is set during the assignment.
I noticed when I took the server to another network.2 and connected it then it did get and except another ip address from the dhcp server there of another range as well, and the gatway as well. But the DNS server was not replaced by the correct one of the other server, it still had the DNS entry supplied by network 1.
I've been able to reproduce this now in 2 new servers.
Is this a known issue for anyone, or should I make a bug ticket in trac?
I noticed when I took the server to another network.2 and connected it then it did get and except another ip address from the dhcp server there of another range as well, and the gatway as well. But the DNS server was not replaced by the correct one of the other server, it still had the DNS entry supplied by network 1.
I've been able to reproduce this now in 2 new servers.
Is this a known issue for anyone, or should I make a bug ticket in trac?
39
Installation and Upgrades / Re: Zarafa 6.4->7 Update
« on: January 05, 2012, 08:51:50 pm »
zarafa still uses MySQL.
40
Installation and Upgrades / Re: Issues with Certification Authority configuration
« on: December 24, 2011, 09:50:24 am »
Please do add that feature indeed.
Can I see this list somewhere, or must I send in a trac ticket for this?
Can I see this list somewhere, or must I send in a trac ticket for this?
41
Installation and Upgrades / Re: Creating more than 1 administration accounts
« on: December 22, 2011, 11:58:53 pm »Hi there,
sudo adduser new_admin admin would do the trick as well. The debian way...
Best,
Robb, the point a bit is that most people expect that there are other "blackbox" items required by zentyal to work for these kind of actions. So its a pleasure to see it does not for this user management. Mostly with gui systems if you start working things on the command line while there is a management system, then things tend to fall apart.
Do you know maybe (or point me to a documentation) what kind of operations can be done cmd style and which not?
42
Installation and Upgrades / Re: Traffic Shaping vs Throttling Bandwidth
« on: December 22, 2011, 11:50:25 pm »
n.p.
The only way I know inside the zentyal scope to get your item 1, or near to it, is to create network objects and then create traffic shaping rules. There you can actually limit the max rate for the source network object.
But these are not user bound then, more PC bound.
The only way I know inside the zentyal scope to get your item 1, or near to it, is to create network objects and then create traffic shaping rules. There you can actually limit the max rate for the source network object.
But these are not user bound then, more PC bound.
43
Installation and Upgrades / Re: Traffic Shaping vs Throttling Bandwidth
« on: December 20, 2011, 11:34:53 pm »
I would think that 2 is the default behavior of the system if you did not implement item-1 and there was no other traffic that has higher priority at that moment...
To my understanding of the matter the RATE == bandwidth effectively, although bandwidth mostly is relative to the total, and Rate would be a max kbps
To my understanding of the matter the RATE == bandwidth effectively, although bandwidth mostly is relative to the total, and Rate would be a max kbps
44
Installation and Upgrades / Re: Create a subdomain on my server
« on: December 15, 2011, 10:03:49 pm »
start here? :
- Have you looked at all DNS server entries? Is the sub created?
- Does your client machine look at that zentyal DNS as source?
- Or when on the server itself, does your network DNS setting use the zentyal DNS server ?
45
Installation and Upgrades / Re: Spam on Zarafa
« on: December 15, 2011, 09:56:37 pm »
Yes, see the setting in /etc/zarafa/dagent.cfg, msg marked with that header info will go to the junk mail folder.
But when you have the antivirus and spam from zentyal configured etc this is set correctly
But when you have the antivirus and spam from zentyal configured etc this is set correctly