Recent Posts
41
Installation and Upgrades / Re: Fresh install hangs after selecting modules
« Last post by gofast321 on October 02, 2024, 08:22:13 pm »Thanks for the response Siroco.
I'm installing version 8.0 development edition
I'm using the GUI expert mode to install
I'm partitioning the the whole 80GB disk without LVM
If I install with just basic network and firewall it finishes fine. If I choose the domain module and/or any other combination of modules, the installation process will just die. It will just hang on one of the install steps (ie. 369 of 380, etc.) If I close the browser and reopen the 'Zentyal Administration" site it will come back to the 'Initial Setup' screen. It will show the modules I already picked as check marked and if I click install again it will show no packages selected. So then the only option is to click "skip install". It will take me directly to the dashboard which shows all the modules installed but the problem is that I never get to complete the initial domain setup.
After doing some testing I stumbled on a weird workaround. After the machine reboots after the base install, if I let it sit at the Zentyal Administrator console for about 5 minutes before choosing the modules then it will normally complete fine. So I'm wondering if there is some weird race condition happening.
Unfortunately I'm not smart enough to diagnose it much deeper than that. Most of my help is only observational.
Thanks,
Chad
I'm installing version 8.0 development edition
I'm using the GUI expert mode to install
I'm partitioning the the whole 80GB disk without LVM
If I install with just basic network and firewall it finishes fine. If I choose the domain module and/or any other combination of modules, the installation process will just die. It will just hang on one of the install steps (ie. 369 of 380, etc.) If I close the browser and reopen the 'Zentyal Administration" site it will come back to the 'Initial Setup' screen. It will show the modules I already picked as check marked and if I click install again it will show no packages selected. So then the only option is to click "skip install". It will take me directly to the dashboard which shows all the modules installed but the problem is that I never get to complete the initial domain setup.
After doing some testing I stumbled on a weird workaround. After the machine reboots after the base install, if I let it sit at the Zentyal Administrator console for about 5 minutes before choosing the modules then it will normally complete fine. So I'm wondering if there is some weird race condition happening.
Unfortunately I'm not smart enough to diagnose it much deeper than that. Most of my help is only observational.
Thanks,
Chad
42
Other modules / Squid error on 8.0
« Last post by francisschappo12 on October 02, 2024, 03:57:51 pm »Hello,
I have the following error in Http Proxy in version 8.0:
× squid.service - Squid Web Proxy Server
Loaded: loaded (/lib/systemd/system/squid.service; disabled; vendor preset: enabled)
Active: failed (Result: exit-code) since Wed 2024-10-02 07:58:03 -03; 5s ago
Docs: man:squid(
Process: 33250 ExecStartPre=/usr/sbin/squid --foreground -z (code=exited, status=0/SUCCESS)
Process: 33253 ExecStart=/usr/sbin/squid --foreground -sYC (code=exited, status=1/FAILURE)
Main PID: 33253 (code=exited, status=1/FAILURE)
CPU: 141ms
out 02 07:58:03 lamicserver squid[33267]: storeDirWriteCleanLogs: Operation aborted.
out 02 07:58:03 lamicserver squid[33267]: FATAL: mimeLoadIcon: cannot parse internal URL: http://lamicserver.lamic.lan:>
out 02 07:58:03 lamicserver squid[33267]: Squid Cache (Version 5.9): Terminated abnormally.
out 02 07:58:03 lamicserver squid[33253]: Squid Parent: squid-1 process 33267 exited with status 1
out 02 07:58:03 lamicserver squid[33253]: Squid Parent: squid-1 process 33267 will not be restarted for 3600 seconds du>
out 02 07:58:03 lamicserver squid[33253]: Exiting due to repeated, frequent failures
out 02 07:58:03 lamicserver squid[33253]: Removing PID file (/run/squid.pid)
out 02 07:58:03 lamicserver systemd[1]: squid.service: Main process exited, code=exited, status=1/FAILURE
out 02 07:58:03 lamicserver systemd[1]: squid.service: Failed with result 'exit-code'.
out 02 07:58:03 lamicserver systemd[1]: Failed to start Squid Web Proxy Server.
I tried reinstalling the module, but it didn't work.
I have the following error in Http Proxy in version 8.0:
× squid.service - Squid Web Proxy Server
Loaded: loaded (/lib/systemd/system/squid.service; disabled; vendor preset: enabled)
Active: failed (Result: exit-code) since Wed 2024-10-02 07:58:03 -03; 5s ago
Docs: man:squid(
Process: 33250 ExecStartPre=/usr/sbin/squid --foreground -z (code=exited, status=0/SUCCESS)
Process: 33253 ExecStart=/usr/sbin/squid --foreground -sYC (code=exited, status=1/FAILURE)
Main PID: 33253 (code=exited, status=1/FAILURE)
CPU: 141ms
out 02 07:58:03 lamicserver squid[33267]: storeDirWriteCleanLogs: Operation aborted.
out 02 07:58:03 lamicserver squid[33267]: FATAL: mimeLoadIcon: cannot parse internal URL: http://lamicserver.lamic.lan:>
out 02 07:58:03 lamicserver squid[33267]: Squid Cache (Version 5.9): Terminated abnormally.
out 02 07:58:03 lamicserver squid[33253]: Squid Parent: squid-1 process 33267 exited with status 1
out 02 07:58:03 lamicserver squid[33253]: Squid Parent: squid-1 process 33267 will not be restarted for 3600 seconds du>
out 02 07:58:03 lamicserver squid[33253]: Exiting due to repeated, frequent failures
out 02 07:58:03 lamicserver squid[33253]: Removing PID file (/run/squid.pid)
out 02 07:58:03 lamicserver systemd[1]: squid.service: Main process exited, code=exited, status=1/FAILURE
out 02 07:58:03 lamicserver systemd[1]: squid.service: Failed with result 'exit-code'.
out 02 07:58:03 lamicserver systemd[1]: Failed to start Squid Web Proxy Server.
I tried reinstalling the module, but it didn't work.
43
Portuguese / Erro no Squid
« Last post by francisschappo12 on October 02, 2024, 12:59:05 pm »Bom dia pessoal,
Estou com o seguinte erro no Http Proxy na versão 8.0:
× squid.service - Squid Web Proxy Server
Loaded: loaded (/lib/systemd/system/squid.service; disabled; vendor preset: enabled)
Active: failed (Result: exit-code) since Wed 2024-10-02 07:58:03 -03; 5s ago
Docs: man:squid(
Process: 33250 ExecStartPre=/usr/sbin/squid --foreground -z (code=exited, status=0/SUCCESS)
Process: 33253 ExecStart=/usr/sbin/squid --foreground -sYC (code=exited, status=1/FAILURE)
Main PID: 33253 (code=exited, status=1/FAILURE)
CPU: 141ms
out 02 07:58:03 lamicserver squid[33267]: storeDirWriteCleanLogs: Operation aborted.
out 02 07:58:03 lamicserver squid[33267]: FATAL: mimeLoadIcon: cannot parse internal URL: http://lamicserver.lamic.lan:>
out 02 07:58:03 lamicserver squid[33267]: Squid Cache (Version 5.9): Terminated abnormally.
out 02 07:58:03 lamicserver squid[33253]: Squid Parent: squid-1 process 33267 exited with status 1
out 02 07:58:03 lamicserver squid[33253]: Squid Parent: squid-1 process 33267 will not be restarted for 3600 seconds du>
out 02 07:58:03 lamicserver squid[33253]: Exiting due to repeated, frequent failures
out 02 07:58:03 lamicserver squid[33253]: Removing PID file (/run/squid.pid)
out 02 07:58:03 lamicserver systemd[1]: squid.service: Main process exited, code=exited, status=1/FAILURE
out 02 07:58:03 lamicserver systemd[1]: squid.service: Failed with result 'exit-code'.
out 02 07:58:03 lamicserver systemd[1]: Failed to start Squid Web Proxy Server.
Já tentei de tudo e o Squid não funciona.
Estou com o seguinte erro no Http Proxy na versão 8.0:
× squid.service - Squid Web Proxy Server
Loaded: loaded (/lib/systemd/system/squid.service; disabled; vendor preset: enabled)
Active: failed (Result: exit-code) since Wed 2024-10-02 07:58:03 -03; 5s ago
Docs: man:squid(
Process: 33250 ExecStartPre=/usr/sbin/squid --foreground -z (code=exited, status=0/SUCCESS)
Process: 33253 ExecStart=/usr/sbin/squid --foreground -sYC (code=exited, status=1/FAILURE)
Main PID: 33253 (code=exited, status=1/FAILURE)
CPU: 141ms
out 02 07:58:03 lamicserver squid[33267]: storeDirWriteCleanLogs: Operation aborted.
out 02 07:58:03 lamicserver squid[33267]: FATAL: mimeLoadIcon: cannot parse internal URL: http://lamicserver.lamic.lan:>
out 02 07:58:03 lamicserver squid[33267]: Squid Cache (Version 5.9): Terminated abnormally.
out 02 07:58:03 lamicserver squid[33253]: Squid Parent: squid-1 process 33267 exited with status 1
out 02 07:58:03 lamicserver squid[33253]: Squid Parent: squid-1 process 33267 will not be restarted for 3600 seconds du>
out 02 07:58:03 lamicserver squid[33253]: Exiting due to repeated, frequent failures
out 02 07:58:03 lamicserver squid[33253]: Removing PID file (/run/squid.pid)
out 02 07:58:03 lamicserver systemd[1]: squid.service: Main process exited, code=exited, status=1/FAILURE
out 02 07:58:03 lamicserver systemd[1]: squid.service: Failed with result 'exit-code'.
out 02 07:58:03 lamicserver systemd[1]: Failed to start Squid Web Proxy Server.
Já tentei de tudo e o Squid não funciona.
44
Installation and Upgrades / Re: Fresh install hangs after selecting modules
« Last post by Siroco on October 02, 2024, 10:39:29 am »Hi,
Could you give more specific details about how you do the installation process? For example:
- Which version of Zentyal are you using?
- What type of installation do you select?
- What configuration options do you use?
- Partitioned
- LVM
- Have you tried installing with only the basic network and firewall modules?
- Is there a difference between successful and failed installations?
- Have you tried doing a clean install of Ubuntu and installing Zentyal on Ubuntu as the official documentation says?
https://doc.zentyal.org/en/installation.html#installation-on-top-of-ubuntu-22-04-lts-server-or-desktop
Regards.
Could you give more specific details about how you do the installation process? For example:
- Which version of Zentyal are you using?
- What type of installation do you select?
- What configuration options do you use?
- Partitioned
- LVM
- Have you tried installing with only the basic network and firewall modules?
- Is there a difference between successful and failed installations?
- Have you tried doing a clean install of Ubuntu and installing Zentyal on Ubuntu as the official documentation says?
https://doc.zentyal.org/en/installation.html#installation-on-top-of-ubuntu-22-04-lts-server-or-desktop
Regards.
45
Installation and Upgrades / Fresh install hangs after selecting modules
« Last post by gofast321 on September 30, 2024, 10:29:56 pm »Hi all. I'm doing a fresh install of v8.0 on a bare metal Dell server and I'm running into a weird issue. Installation seems to go fine but when I get to the point to select the initial modules (domain and DNS ) it hangs during the install. It doesn't matter which modules I select for the installation. The machine still responds but the installation process of the modules just gives up. It will hang at random points in the installation process but never the same place. I did have it complete successfully once but out of the 10 times I have tried, 9 of them have failed.
I also attempted to install in a VirtualBox VM and got the same results. Has anyone else seen this? Any workarounds?
Thanks,
Chad
I also attempted to install in a VirtualBox VM and got the same results. Has anyone else seen this? Any workarounds?
Thanks,
Chad
46
Installation and Upgrades / Re: update.zentyal.org is down
« Last post by turalyon on September 11, 2024, 03:13:37 pm »The packages zentyal-core 7.1.3 and zentyal-core 7.0.10 were released a month ago, and one of the fixes contains a solution for this issue.
- https://github.com/zentyal/zentyal/commit/bcce6f23e48395100b8d1b3ad6e20e5f05f2cb3d
- https://github.com/zentyal/zentyal/commit/a0c683e1306a58883dddf6194b478e10eeaff3d9
—
This world is ours, and by the Holy Light, we will keep it safe, now and forever.
- https://github.com/zentyal/zentyal/commit/bcce6f23e48395100b8d1b3ad6e20e5f05f2cb3d
- https://github.com/zentyal/zentyal/commit/a0c683e1306a58883dddf6194b478e10eeaff3d9
—
This world is ours, and by the Holy Light, we will keep it safe, now and forever.
47
Installation and Upgrades / Re: Upgrade zentyal
« Last post by turalyon on September 11, 2024, 03:06:15 pm »Hi,
Below you have the command that downloads the repository key for Zentyal 7.1 Development:
The repository ‘/etc/apt/sources.list.d/zentyal.list’ should be configured as follows:
If the issue persists, you should check the server's time, it might be wrong, and because of that, the certificate error.
—
This world is ours, and by the Holy Light, we will keep it safe, now and forever.
Below you have the command that downloads the repository key for Zentyal 7.1 Development:
Code: [Select]
wget -q https://keys.zentyal.org/zentyal-7.1-packages-org.asc -P /etc/apt/trusted.gpg.d/zentyal-7.1-packages-org.asc
The repository ‘/etc/apt/sources.list.d/zentyal.list’ should be configured as follows:
Code: [Select]
deb [signed-by=/etc/apt/trusted.gpg.d/zentyal-7.1-packages-org.asc] https://packages.zentyal.org/zentyal 7.1 main extra
If the issue persists, you should check the server's time, it might be wrong, and because of that, the certificate error.
—
This world is ours, and by the Holy Light, we will keep it safe, now and forever.
48
Installation and Upgrades / Re: zentyal 7.0.9 stop allow webadmin login
« Last post by aehimself on September 10, 2024, 08:11:37 am »You are probably affected by update.zentyal.org being down.
Check if the solution linked to the GitHub issue is applicable to your installation.
Check if the solution linked to the GitHub issue is applicable to your installation.
49
Installation and Upgrades / zentyal 7.0.9 stop allow webadmin login
« Last post by imresz on September 10, 2024, 12:01:42 am »Hello
I have two 7.0.9 server (one for file sharing and one for mailing)
email and fileshares are OK, but I unable to log in webadmin
zs webadmin status is seens work, and I not updated the servers, but it already want to dpkg --configure -a the zentyal-core package. I start the procedure but nothing happens.
Is there anyone with same problem?
sudo dpkg --configure -a
Setting up zentyal-core (7.0.9) ...
Best Regards
Imre Szollosi
I have two 7.0.9 server (one for file sharing and one for mailing)
email and fileshares are OK, but I unable to log in webadmin
zs webadmin status is seens work, and I not updated the servers, but it already want to dpkg --configure -a the zentyal-core package. I start the procedure but nothing happens.
Is there anyone with same problem?
sudo dpkg --configure -a
Setting up zentyal-core (7.0.9) ...
Best Regards
Imre Szollosi
50
Installation and Upgrades / Re: update.zentyal.org is down
« Last post by Adelson on September 09, 2024, 08:12:55 pm »Hi aehimself.
Yes, I have used a similar tool and confirmed that update.zentyal.org is down.
It seems that this issue indeed affects the webadmin interface which returns a Gateway Time-out error.
I have just found a solution here in the forum which leads to this thread
https://github.com/zentyal/zentyal/issues/2112
Yes, I have used a similar tool and confirmed that update.zentyal.org is down.
It seems that this issue indeed affects the webadmin interface which returns a Gateway Time-out error.
I have just found a solution here in the forum which leads to this thread
https://github.com/zentyal/zentyal/issues/2112