Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
46
Installation and Upgrades / Re: Changing mail location
« on: October 25, 2012, 05:20:00 am »
Why just not mount your drives under /var/mail ?
47
Installation and Upgrades / Re: Software raid immediately shows degraded
« on: October 24, 2012, 01:13:05 pm »
Do you have all of the drives plugged into the motherboard or are some drives plugged into pci sata card or something like that?
I have had some issues with my raid 1 setup when using a cheap pci sata card.... one drive plugged into the car and one into the motherboard. I would have issues with the drives loosing sync (this issue was only with my OS drives). I now have both plugged into the motherboard with no issues (Since my last restart of the server it has been 70 days and I have had 0 issues).
I have had some issues with my raid 1 setup when using a cheap pci sata card.... one drive plugged into the car and one into the motherboard. I would have issues with the drives loosing sync (this issue was only with my OS drives). I now have both plugged into the motherboard with no issues (Since my last restart of the server it has been 70 days and I have had 0 issues).
48
Installation and Upgrades / Re: Software raid immediately shows degraded
« on: October 24, 2012, 12:52:25 pm »
Reano - from my experience I believe this is just the case with software raid. It has to sync all the drives in the beginning..... in your case you just so much space that it can take a while.
I use MDADM software raid on all my linux servers. I have several raid1 setups and one raid 6 spanning 7 x2TB drives. I remember in the beginning it had to sync the raid set, but since the first sync I don't believe I have had any issues.
I use MDADM software raid on all my linux servers. I have several raid1 setups and one raid 6 spanning 7 x2TB drives. I remember in the beginning it had to sync the raid set, but since the first sync I don't believe I have had any issues.
49
Installation and Upgrades / Traffic Shaping Zentya 2.2 - possible issue
« on: October 23, 2012, 05:09:58 pm »
Good Day,
I have a zentyal 2.2 server running as my gateway, proxy, traffic filter, + almost all other modules.
On the server I have also installed subsonic which runs on port 4040 and is accessible from the outside.
I also have another subsonic server internally on my LAN which listens on port 80 and is accessible from the outside through the use of a reverse proxy.
I can access both subsonic servers with no issue and I can either listen to music or stream video content depending on which server I connect to.
I have recently tried to implement some traffic shaping rules for these two servers since I have very limited upload bandwidth (3 Mb/s). I have configured the rate of my external interface for both upload and download.
In the traffic shaping module I created a port based rule on the external interface that would limit upload traffic from subsonic on port 4040 to 1000 Kb/s. I have also created a Layer-7 filter that listens for any music or video and limits it to 1000 Kb/s.
However I do not see the rate being limited at all..... Is there a way I can check to see if the traffic filter is working? It seems that no matter what max limit I put into the traffic filter for either rule nothing actually happens.
Any ideas?
I have a zentyal 2.2 server running as my gateway, proxy, traffic filter, + almost all other modules.
On the server I have also installed subsonic which runs on port 4040 and is accessible from the outside.
I also have another subsonic server internally on my LAN which listens on port 80 and is accessible from the outside through the use of a reverse proxy.
I can access both subsonic servers with no issue and I can either listen to music or stream video content depending on which server I connect to.
I have recently tried to implement some traffic shaping rules for these two servers since I have very limited upload bandwidth (3 Mb/s). I have configured the rate of my external interface for both upload and download.
In the traffic shaping module I created a port based rule on the external interface that would limit upload traffic from subsonic on port 4040 to 1000 Kb/s. I have also created a Layer-7 filter that listens for any music or video and limits it to 1000 Kb/s.
However I do not see the rate being limited at all..... Is there a way I can check to see if the traffic filter is working? It seems that no matter what max limit I put into the traffic filter for either rule nothing actually happens.
Any ideas?
50
Installation and Upgrades / Re: ActiveSync client not synchronize contacts and calendar
« on: October 10, 2012, 09:29:42 pm »
I tried this morning to connect my droid phone to zarafa active sync on my zentyal 3.0 test server. However it would not sync at all. It just told me that authentication failed......
Not sure what is going on.... will probably not have time to dig into it for while.
Not sure what is going on.... will probably not have time to dig into it for while.
51
Installation and Upgrades / Re: ActiveSync client not synchronize contacts and calendar
« on: October 09, 2012, 08:10:48 pm »
Mine is Zentyal 2.2; I do have zpush upgraded to 2.2 and I do run webapp front end. I have a test zentyal 3.0 and I will try it when I have some time.
52
Installation and Upgrades / Re: ActiveSync client not synchronize contacts and calendar
« on: October 09, 2012, 01:02:40 pm »
I have mine running on 443 and it syncs calendars and contacts over SSL. I have several android phones and they all work fine.... actually I even have it going through a reverse proxy first.
You have to make sure your port 443 works first (you have to change your zentyal administration port to something else and then activate SSL under the web-server module) Once SSL is working and you can see the standard Apache it works screen when visiting the site your HTTPS, you should be able to setup active sync by following the directions provided.
Test if the page works by visiting https://your.domain/Microsoft-Server-ActiveSync through a regular browser. See if it even comes up.... if you are successful I believe you see an error that says something along the lines this is for mobile devices only or your browser does not support this connection. Either way you will know that it is working.... at that point you just have to setup active sync on the phone properly.
You have to make sure your port 443 works first (you have to change your zentyal administration port to something else and then activate SSL under the web-server module) Once SSL is working and you can see the standard Apache it works screen when visiting the site your HTTPS, you should be able to setup active sync by following the directions provided.
Test if the page works by visiting https://your.domain/Microsoft-Server-ActiveSync through a regular browser. See if it even comes up.... if you are successful I believe you see an error that says something along the lines this is for mobile devices only or your browser does not support this connection. Either way you will know that it is working.... at that point you just have to setup active sync on the phone properly.
53
Installation and Upgrades / Re: External server getting users from LDAP???
« on: September 19, 2012, 09:21:32 pm »
I only have one Zentyal server and not a master slave setup.... this is why I was asking if I can still authenticate against LDAP from an external server. My zentyal runs user and file sharing modules so it is a standalone install.
The Alfresco and subsonic servers are seperate systems running in my LAN ...... I guess I will just have to try and see if it works
The Alfresco and subsonic servers are seperate systems running in my LAN ...... I guess I will just have to try and see if it works
54
Installation and Upgrades / Re: External server getting users from LDAP???
« on: September 19, 2012, 07:02:29 pm »
Thanks...
I just was not sure if it would work because I know for the standard master slave architecture on zentyal 2.2 you can't have any other modules on the master LDAP server. If you do have user modules the system does not sync, but I was not sure if that applied to authentication only.
I just was not sure if it would work because I know for the standard master slave architecture on zentyal 2.2 you can't have any other modules on the master LDAP server. If you do have user modules the system does not sync, but I was not sure if that applied to authentication only.
55
Installation and Upgrades / External server getting users from LDAP???
« on: September 19, 2012, 06:32:16 pm »
Good Day,
I have zentyal 2.2 running with almost all modules installed. Inside my network I also have an Alfresco and Subsonic server running.
Is it possible to setup LDAP authentication between those servers and Zentyal?? I know when Subsonic is installed on the same server as Zentyal you can make it use LDAP authentication, but in this case it is a separate server. Also since I don't have a master slave architecture I do not know if this is possible.
If all I want is just user authentication should I just open the LDAP port on Zentyal and then just Point Subsonic or Alfresco to it??
Any direction would be great !!!
Thank you !!
I have zentyal 2.2 running with almost all modules installed. Inside my network I also have an Alfresco and Subsonic server running.
Is it possible to setup LDAP authentication between those servers and Zentyal?? I know when Subsonic is installed on the same server as Zentyal you can make it use LDAP authentication, but in this case it is a separate server. Also since I don't have a master slave architecture I do not know if this is possible.
If all I want is just user authentication should I just open the LDAP port on Zentyal and then just Point Subsonic or Alfresco to it??
Any direction would be great !!!
Thank you !!
56
Installation and Upgrades / Re: OpenVPN Extremely Slow, Help!
« on: September 06, 2012, 05:48:47 pm »
I will try implamenting this..... thank you for info !!
57
Installation and Upgrades / Re: /root partion filling up ???
« on: August 16, 2012, 09:46:56 pm »
Thank you for explaining what /var/cache/zentyal/duplicity does
I will look at moving it to another location (maybe use a small 5 gig partition just for duplicity)
Now as far as resizing root: Unfortunately I did not create an LVM partition for root. I am using LVM for /home , but root is a regular partition.
Thank you for your help !!!
I will look at moving it to another location (maybe use a small 5 gig partition just for duplicity)
Now as far as resizing root: Unfortunately I did not create an LVM partition for root. I am using LVM for /home , but root is a regular partition.
Thank you for your help !!!
58
Installation and Upgrades / Re: /root partion filling up ???
« on: August 16, 2012, 05:45:12 pm »
Yes I did that and found it is /var/cache/zentyal is the biggest at 1.8 gigs.
After that it is /var/cache/apt at 367 M
If I break down /var/cache/zentyal I see that the 1.8 gigs is being taken up by /var/cache/zentyal/duplicity....
Any thoughts on this or what to do ?? Can I just erase these ??
Thank you !!
After that it is /var/cache/apt at 367 M
If I break down /var/cache/zentyal I see that the 1.8 gigs is being taken up by /var/cache/zentyal/duplicity....
Any thoughts on this or what to do ?? Can I just erase these ??
Thank you !!
59
Installation and Upgrades / /root partion filling up ???
« on: August 16, 2012, 03:22:18 pm »
Hello Forum Members,
I am running zentyal 2.2.x (latest production version with everything upgraded). The system runs good for the most part with no issues unless I am the one causing them.
However I do have a question with regards to my ever expending /root partition.
I have my system installed on a software raid 1 which consists of two SSD drives. I have given /root partition 10 gigs.
On another SSD drive I have a partition for /var/logs which has 5 gigs. /home is mounted on a different raid1 array.
When I first installed zentyal .... the system was taking up 6 gigs of my system drive + 1 gig for proxy cache.
Since then the system just keeps growing and now it is taking up over 7.5 gigs. This 7.5 gigs + 1 gig for proxy cache only leaves just a bit over 1 gig free and with the system expending it will eat that up quickly.
I don't understand what is making the system keep growing and growing (sine my last complete reinstall it has only been 3 weeks). My logs are on a separate disk so that should be not causing the expansion. I back up the system to another server so no backups should be on zentyal itself.
When I break the /root partition down to see what is taking up the most space I find that /usr is about 1.9 gigs and /var is about 5.6 gigs. In var I find that /var/cache is over 2 gigs (this is the biggest chunk)..... does this seem normal
My question is this normal for the system to keep growing like this
How can I move /var to a new partition? I have another raid1 array with about 10 gigs which I can allocate to just /var This should give me a lot more space.
I am running zentyal 2.2.x (latest production version with everything upgraded). The system runs good for the most part with no issues unless I am the one causing them.
However I do have a question with regards to my ever expending /root partition.
I have my system installed on a software raid 1 which consists of two SSD drives. I have given /root partition 10 gigs.
On another SSD drive I have a partition for /var/logs which has 5 gigs. /home is mounted on a different raid1 array.
When I first installed zentyal .... the system was taking up 6 gigs of my system drive + 1 gig for proxy cache.
Since then the system just keeps growing and now it is taking up over 7.5 gigs. This 7.5 gigs + 1 gig for proxy cache only leaves just a bit over 1 gig free and with the system expending it will eat that up quickly.
I don't understand what is making the system keep growing and growing (sine my last complete reinstall it has only been 3 weeks). My logs are on a separate disk so that should be not causing the expansion. I back up the system to another server so no backups should be on zentyal itself.
When I break the /root partition down to see what is taking up the most space I find that /usr is about 1.9 gigs and /var is about 5.6 gigs. In var I find that /var/cache is over 2 gigs (this is the biggest chunk)..... does this seem normal
My question is this normal for the system to keep growing like this
How can I move /var to a new partition? I have another raid1 array with about 10 gigs which I can allocate to just /var This should give me a lot more space.
60
Installation and Upgrades / Re: User's Corner
« on: August 15, 2012, 09:38:04 pm »
You should just have to create a rule in zentyal firewall under external networks to zentyal.
Something like
FROM: Any
Source Port: Any
Destination: Usercorner
User Corner uses port 8888 by default. So you would have to point your external client to https://yourserverIP:8888
Something like
FROM: Any
Source Port: Any
Destination: Usercorner
User Corner uses port 8888 by default. So you would have to point your external client to https://yourserverIP:8888