Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
1
Installation and Upgrades / TypeError: Zentyal.escapeHTTPQuery is not a function
« on: July 28, 2015, 12:31:28 pm »
After installation of Zentyal development edition 4.1 I try to install some package:
select some components and click on install.
Wait a second for the confirmation box and click continue.
Nothing. Click again. Nothing.
Open che browser console ( F12 ) i see the error:
TypeError: Zentyal.escapeHTTPQuery is not a function
The same error in the system update ( function doUpdates(title) ).
Thank you,
Rickyx
select some components and click on install.
Wait a second for the confirmation box and click continue.
Nothing. Click again. Nothing.
Open che browser console ( F12 ) i see the error:
TypeError: Zentyal.escapeHTTPQuery is not a function
The same error in the system update ( function doUpdates(title) ).
Thank you,
Rickyx
2
Installation and Upgrades / Error occurred while mounting home
« on: December 29, 2014, 12:36:16 am »
Hi to everybody.
I'm installing Zentyal on a machine with 3 hd: one for /boot and / , the other two in Raid1 for swap and /home. I would like to encrypt /, /home and swap.
I have tried several times with different partition layer (with raid, without raid, Mbr, Guid and lot's of other possibility) and the result is always the same:
I install Zentyal, I'm so happy and everything is working but...
But as soon as I complete the configuration and I restart the machine I receive the message as in subject: Error occurred while mounting home.
No other details or complaints. (Attached you see the screen.)
I suppose is likely to be Ubuntu related but I'm not sure.
In previous versions of Zentyal I used similar configurations and everything worked smooth.
How I can inspect what really is causing the error?
There are known problems with home encryption?
Thank you,
Rickyx
ps. I also tried to remove raid and using the second hd for "classic" backup and keeping only encryption layer: the error was the same.
I'm installing Zentyal on a machine with 3 hd: one for /boot and / , the other two in Raid1 for swap and /home. I would like to encrypt /, /home and swap.
I have tried several times with different partition layer (with raid, without raid, Mbr, Guid and lot's of other possibility) and the result is always the same:
I install Zentyal, I'm so happy and everything is working but...
But as soon as I complete the configuration and I restart the machine I receive the message as in subject: Error occurred while mounting home.
No other details or complaints. (Attached you see the screen.)
I suppose is likely to be Ubuntu related but I'm not sure.
In previous versions of Zentyal I used similar configurations and everything worked smooth.
How I can inspect what really is causing the error?
There are known problems with home encryption?
Thank you,
Rickyx
ps. I also tried to remove raid and using the second hd for "classic" backup and keeping only encryption layer: the error was the same.
3
Installation and Upgrades / [[Solved]] Samba slow if gateway
« on: January 07, 2012, 05:52:41 pm »
Zentyal 2.2.4
If I setup ONLY one interface and Dhcp, clients read and write fast on samba shares: 11 Mb/s on a 10/100 network.
If I setup Zentyal as the attached image client use samba around 20 kb/s. Internet is fast as it should be.
Of course I exclude any kind of hardware failure, network connections and card, hard disk malfunctioning.
Checked logs but I can't see problems that can be related to this behavior.
I have tried all kind of voodoo but I can't solve the problem.
Thank you for any kind of suggestion that can help me to solve the problem.
Riccardo
If I setup ONLY one interface and Dhcp, clients read and write fast on samba shares: 11 Mb/s on a 10/100 network.
If I setup Zentyal as the attached image client use samba around 20 kb/s. Internet is fast as it should be.
Of course I exclude any kind of hardware failure, network connections and card, hard disk malfunctioning.
Checked logs but I can't see problems that can be related to this behavior.
I have tried all kind of voodoo but I can't solve the problem.
Thank you for any kind of suggestion that can help me to solve the problem.
Riccardo
4
Installation and Upgrades / [SOLVED] Ubuntu Desktop - Export Shares
« on: November 16, 2011, 01:37:48 pm »
Everything works fine with Windows clients.
Installed Ubuntu Desktop on a experimental Ubuntu workstation.
Home share is correctly exported.
How to tell Zentyal/Client to automatically export available shares for that specific user?
Tried to look aroud but I did not found a clear solution.
Ubuntu 11.10
Zentyal 2.0.23
Thank you,
Rickyx
Installed Ubuntu Desktop on a experimental Ubuntu workstation.
Home share is correctly exported.
How to tell Zentyal/Client to automatically export available shares for that specific user?
Tried to look aroud but I did not found a clear solution.
Ubuntu 11.10
Zentyal 2.0.23
Thank you,
Rickyx
5
Installation and Upgrades / Unix permission of samba share.
« on: September 28, 2010, 09:48:47 am »
Hi,
i did like a mess changing permission, owner and group of samba shares. Now is fine but I'm not happy with having 777 everywere...
Witch is the default user and group that directory under samba has?
(Currently I'm away from office...!)
Thank you,
Ricky
i did like a mess changing permission, owner and group of samba shares. Now is fine but I'm not happy with having 777 everywere...
Witch is the default user and group that directory under samba has?
(Currently I'm away from office...!)
Thank you,
Ricky
6
Installation and Upgrades / Interface configuration
« on: September 13, 2010, 04:57:19 pm »
Hi,
my server has who interfaces eth0 and eth1. I set up from the Zentyal panel the following configuration:
eth0 (esternal)
address 10.10.10.11
mask 255.255.255.0
gateway 10.10.10.10
eth1 (internal)
address 10.10.10.12
mask 255.255.255.0
I edited /etc/network/interfaces I wrote the same configuration. Where Zentyal reallly store the configuration as, for what I understand, not in /etc/network/interfaces ?
And there maybe some problems internal to Zentyal that cause that I can't ping both interfaces?
Thank you very much,
Ricky.
my server has who interfaces eth0 and eth1. I set up from the Zentyal panel the following configuration:
eth0 (esternal)
address 10.10.10.11
mask 255.255.255.0
gateway 10.10.10.10
eth1 (internal)
address 10.10.10.12
mask 255.255.255.0
I edited /etc/network/interfaces I wrote the same configuration. Where Zentyal reallly store the configuration as, for what I understand, not in /etc/network/interfaces ?
And there maybe some problems internal to Zentyal that cause that I can't ping both interfaces?
Thank you very much,
Ricky.
7
Installation and Upgrades / File server
« on: July 31, 2010, 11:26:37 am »
Hi to all!
This is my first post: I found this project and it is really interesting.
I'm italian and my job is architecture (not software, real buildings!)... but I'm Linuxian/Debianist since high school.
So now that where I work (little office, 15 people ) has to upgrade the server (an old NT4 working perfectly 346/7/24 since 2000) they proposed me to switch to Linux. Not really for a need (the other option of course is Windows Server) but for 50% for an ideal and the rest for some problems with CAL licenses. Client maybe will be, slowly, switched too.
The server we are buying is a Fujitsu TX150 S7 and I would like to set up EBox on it.
For the moment I just tried version 1.5 on VirtualBox on my laptop and it worked fine.
I normally start from a Debian net-install but I never got to have a so nice web-interface to control the server!!
I read this 1.5 is a dev version: not a problem because in the first period old and new server will stay close to avoid surprises
But how EBox deals with updates? Will I be able to switch to 2.0 (and possibly further) just as "sudo apt-get update"? And normally EBox tries to install security updates?
Thank you,
Riccardo
This is my first post: I found this project and it is really interesting.
I'm italian and my job is architecture (not software, real buildings!)... but I'm Linuxian/Debianist since high school.
So now that where I work (little office, 15 people ) has to upgrade the server (an old NT4 working perfectly 346/7/24 since 2000) they proposed me to switch to Linux. Not really for a need (the other option of course is Windows Server) but for 50% for an ideal and the rest for some problems with CAL licenses. Client maybe will be, slowly, switched too.
The server we are buying is a Fujitsu TX150 S7 and I would like to set up EBox on it.
For the moment I just tried version 1.5 on VirtualBox on my laptop and it worked fine.
I normally start from a Debian net-install but I never got to have a so nice web-interface to control the server!!
I read this 1.5 is a dev version: not a problem because in the first period old and new server will stay close to avoid surprises
But how EBox deals with updates? Will I be able to switch to 2.0 (and possibly further) just as "sudo apt-get update"? And normally EBox tries to install security updates?
Thank you,
Riccardo
Pages: [1]