This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
1
Installation and Upgrades / Re: sending mail from external interface fails
« on: May 22, 2011, 12:19:54 pm »
there is no service on port 587 in zentyal.
I can telnet to both 25 and 465.
If the outgoing server in Evolution is the TAP address, everything works fine. If it is the external address, nothing.
I can telnet to both 25 and 465.
If the outgoing server in Evolution is the TAP address, everything works fine. If it is the external address, nothing.
2
Installation and Upgrades / sending mail from external interface fails
« on: May 22, 2011, 11:07:34 am »
I have set up the mail for my domain. Everything works fine except sending e-mails from external interfaces.
SMTP is configured with TLS and auth. Connecting to internal/tap interface sends the e-mail. Connecting to external interface fails. Port 465 is open (nmap) and accepting connections.
What do I have to do to be able to send mail through external interface?
Thanks
Matija
SMTP is configured with TLS and auth. Connecting to internal/tap interface sends the e-mail. Connecting to external interface fails. Port 465 is open (nmap) and accepting connections.
What do I have to do to be able to send mail through external interface?
Thanks
Matija
3
Installation and Upgrades / Samba over VPN bug
« on: August 02, 2010, 10:39:50 am »
in smb.conf, interfaces were defined as:
lo, eth0, tap-1
there is only tap0, manually changed it to tap0 and everything works ok.
Hope this helps
lo, eth0, tap-1
there is only tap0, manually changed it to tap0 and everything works ok.
Hope this helps
4
Installation and Upgrades / Re: Problems sending email via smarthost
« on: July 04, 2009, 02:17:14 pm »
Put ip address of the smarthost server
5
Installation and Upgrades / Re: VPN and Windows Shares
« on: June 11, 2009, 01:14:39 am »
It works ...
I have two "unusual" lines in my firewall, first under internal networks: accept/any/any/any
the second under external to internal (this may seem strange) accept/vpn/any/any
where vpn object is the vpn range. These rules are from an older version, they may not be needed now.
I have two "unusual" lines in my firewall, first under internal networks: accept/any/any/any
the second under external to internal (this may seem strange) accept/vpn/any/any
where vpn object is the vpn range. These rules are from an older version, they may not be needed now.
6
Installation and Upgrades / Re: Samba PDC problems after migration
« on: May 04, 2009, 12:23:37 am »
After several weeks I finally found the time to repeat the process with the updated version.
Smooth. Users did not notice anything.
Smooth. Users did not notice anything.
7
Installation and Upgrades / Re: Newbie: set up for routing (internet sharing)
« on: May 03, 2009, 11:39:13 pm »
Gateway must be set manually!
Generally speaking, I gave up using anything except "static" for NICs (ok, i use trunk, but then again static for vlans) on EBOX. This way it works great. Make dsl router dial, and give ebox a fixed address and then put it in the DMZ on dls router.
Matija
Generally speaking, I gave up using anything except "static" for NICs (ok, i use trunk, but then again static for vlans) on EBOX. This way it works great. Make dsl router dial, and give ebox a fixed address and then put it in the DMZ on dls router.
Matija
8
Installation and Upgrades / Re: Samba PDC problems after migration
« on: April 06, 2009, 03:36:42 pm »
Just a small update until this issue is resolved.
Javi was very helpful on IRC, we tried migration step by step and the outcome was the same.
I have to solve this and once I do, I will post a report.
Matija
Javi was very helpful on IRC, we tried migration step by step and the outcome was the same.
I have to solve this and once I do, I will post a report.
Matija
9
Installation and Upgrades / Re: Samba PDC problems after migration
« on: April 05, 2009, 08:12:23 pm »Quote
you must supply the wanted domain SID portion at /usr/share/ebox-samba/ebox-fix-sid line 34
What are the argumens?
10
Installation and Upgrades / Re: Can i use Ebox as a router?
« on: April 05, 2009, 08:07:29 pm »
if you have ethernet connection (and not PPPoE or something)
eth0 - dhcp, check external
eth1 - static 192.168.1.1/24
eth2 - static 192.168.2.1/24
gateway - now, usually there is only one gateway for your provider, so whatever you get over dhcp, put it here
dns (network)- same thing
then in firewall in internal set (this is for internal to internal and to internet) any, any, any
eth0 - dhcp, check external
eth1 - static 192.168.1.1/24
eth2 - static 192.168.2.1/24
gateway - now, usually there is only one gateway for your provider, so whatever you get over dhcp, put it here
dns (network)- same thing
then in firewall in internal set (this is for internal to internal and to internet) any, any, any
11
Installation and Upgrades / Re: problem joining Windows XP machines to Ebox domain
« on: April 05, 2009, 08:00:53 pm »
I had this many times until i figured that the problem was with the workstation names.
The worksations are not removed correctly, when you remove them from a domain and you can not insert another worksation with the same name.
sudo smbldap-userlist
sudo smbldap-userdel workstationX$ #(note $ at the end)
removes old entries and then it works normaly.
Matija
The worksations are not removed correctly, when you remove them from a domain and you can not insert another worksation with the same name.
sudo smbldap-userlist
sudo smbldap-userdel workstationX$ #(note $ at the end)
removes old entries and then it works normaly.
Matija
12
Installation and Upgrades / Re: Samba PDC problems after migration
« on: April 05, 2009, 07:55:04 pm »
No.
I have a feeling that the workstation is in "another" domain with the same name.
Can this be sids issue?
Matija
I have a feeling that the workstation is in "another" domain with the same name.
Can this be sids issue?
Matija
13
Installation and Upgrades / Samba PDC problems after migration
« on: April 05, 2009, 11:56:37 am »
I migrated eBOX. First I ulpoaded the configuration backup, then /var/vmail, /home/samba/users, /home/samba/groups.
home/samba/profiles are part of configuration backup (strange behaviour since roaming profiles change all the time). This process was not smooth.
Anyway, now I have one unresolved issue: when I log on at a workstation with an account that is supposed to be domain admin, I have no administration rights.
I checked with smbldap-groupshow "Domain Admins" and this user is in the group. I also removed the workstation from the domain and then removed it with smbldap-userdel ws1$ and then put it back into domain using this user's login/passwword. This worked, but the user still has no administration rights on the workstation.
I need help on this.
Matija
home/samba/profiles are part of configuration backup (strange behaviour since roaming profiles change all the time). This process was not smooth.
Anyway, now I have one unresolved issue: when I log on at a workstation with an account that is supposed to be domain admin, I have no administration rights.
I checked with smbldap-groupshow "Domain Admins" and this user is in the group. I also removed the workstation from the domain and then removed it with smbldap-userdel ws1$ and then put it back into domain using this user's login/passwword. This worked, but the user still has no administration rights on the workstation.
I need help on this.
Matija
14
Installation and Upgrades / Thin Client
« on: March 21, 2009, 01:51:26 pm »
ebox 1.0
It is not clear how to set it up, nor what it can do.
What I would like to do is netboot the stations. I tried to upload a .iso file, set ebox as server. A client gets an IP address, and reports a missing file.
The manual is not helpuf.
Please help.
Matija
It is not clear how to set it up, nor what it can do.
What I would like to do is netboot the stations. I tried to upload a .iso file, set ebox as server. A client gets an IP address, and reports a missing file.
The manual is not helpuf.
Please help.
Matija
15
Installation and Upgrades / Re: file and print server for xp clients
« on: March 18, 2009, 07:36:25 pm »
I have eboxes running in similar eviroments (though not schools).
Roaming profiles are OK for this. You need to reinstall the workstations. Then follow http://www.pcc-services.com/articles/implement_sys_policies.html to setup policies. Be restrictive.
I prefere Kasperski.
Roaming profiles are OK for this. You need to reinstall the workstations. Then follow http://www.pcc-services.com/articles/implement_sys_policies.html to setup policies. Be restrictive.
I prefere Kasperski.
Pages: [1] 2