This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
46
Spanish / Re: Espacio en disco duro
« on: January 04, 2014, 11:38:28 am »
Sin saber que ocupa el espacio de disco, no hay diagnostico posible.
Tienes que averiguar de que se está llenando el file system para saber de quien es la culpa.
Tienes que averiguar de que se está llenando el file system para saber de quien es la culpa.
47
Si te he comprendido bien, usabas vlan tagging para crear una vlan para un access point wifi.
Ya no usas el access point y has eliminado la vlan, pero obtienes un error relativo a la vlan eliminada cada vez que guardas lo cambios?
Si este es el caso, yo mismo estoy investigando un problema similar.
Tengo una copia de mi servidor en otro HW con un interface menos y también se me queja del interface que falta.
Si encuentro una solución, te la pongo por aquí.
Ya no usas el access point y has eliminado la vlan, pero obtienes un error relativo a la vlan eliminada cada vez que guardas lo cambios?
Si este es el caso, yo mismo estoy investigando un problema similar.
Tengo una copia de mi servidor en otro HW con un interface menos y también se me queja del interface que falta.
Si encuentro una solución, te la pongo por aquí.
48
Spanish / Re: Voip en Zentyal 3.3
« on: January 04, 2014, 11:22:48 am »
Como dice ROBB, esos módulos se han caído de las nuevas versiones.
Sin embargo, puedes instalar asterisk a mano sin problemas.
Sin embargo, puedes instalar asterisk a mano sin problemas.
49
Spanish / Re: problema sobre configurar la red
« on: January 04, 2014, 11:20:37 am »
Desde la maquina zentyal tienes internet?
Diferencia si el problema es de conectividad o de DNS. Para ello usa:
ping 8.8.8.8 si funciona, tienes conectividad.
ping google.com si falla, el problema es de DNS
Diferencia si el problema es de conectividad o de DNS. Para ello usa:
ping 8.8.8.8 si funciona, tienes conectividad.
ping google.com si falla, el problema es de DNS
50
Spanish / Re: Zarafa falla despues de actualizar desde la version 3.2 a la 3.3.
« on: January 04, 2014, 11:17:25 am »
Parece que le ha ocurrido a más gente. En el foro general he leído algún caso y hay un ticket al respecto:
http://trac.zentyal.org/ticket/7894
http://forum.zentyal.org/index.php/topic,19381.30.html
En algunos casos, parece que le problema se resuelve quitando el modulo webmail:
http://forum.zentyal.org/index.php/topic,19402.new.html#new
http://trac.zentyal.org/ticket/7894
http://forum.zentyal.org/index.php/topic,19381.30.html
En algunos casos, parece que le problema se resuelve quitando el modulo webmail:
http://forum.zentyal.org/index.php/topic,19402.new.html#new
51
Spanish / Re: Error al descargar Zentyal 3.3
« on: January 04, 2014, 11:03:20 am »
http://sourceforge.net/projects/zentyal/files/?source=navbar
Yo descargue la 3.3 hace unas semanas sin problemas.
Yo descargue la 3.3 hace unas semanas sin problemas.
52
Spanish / Re: tiempo de inicio: 11minutos!
« on: January 04, 2014, 11:00:52 am »
¿te refieres que al cambiar el disco del sistema a un nuevo hardware ha arrancado más rapido?
Una de dos, o tu HW falla o en el nuevo HW no han arrancado bien los servicios. Esto puede ser porque los interfaces de red son diferentes y UDEV recuerda los antiguos y les asigna nombres consecutivos a los nuevos.
Respecto al tiempo que tarda en guardar cambios, ¿en que paso se queda todo ese tiempo?
Una de dos, o tu HW falla o en el nuevo HW no han arrancado bien los servicios. Esto puede ser porque los interfaces de red son diferentes y UDEV recuerda los antiguos y les asigna nombres consecutivos a los nuevos.
Respecto al tiempo que tarda en guardar cambios, ¿en que paso se queda todo ese tiempo?
53
Installation and Upgrades / Re: Zentyal 3.2.3, Samba hangs on 67%, doesn't continue to 100%... Any ideas???
« on: January 03, 2014, 10:32:29 am »
Confirmed same issue in 3.2.
I have left it run for 48h+ and same 67% progress so i think some process hangs with large number of files shares. It is probably related to ACL.
This is a severe issue in a basic service...
ticket:
http://trac.zentyal.org/ticket/7972
I have left it run for 48h+ and same 67% progress so i think some process hangs with large number of files shares. It is probably related to ACL.
This is a severe issue in a basic service...
ticket:
http://trac.zentyal.org/ticket/7972
54
Spanish / Re: Zarafa falla despues de actualizar desde la version 3.2 a la 3.3.
« on: January 02, 2014, 10:23:10 am »
Lo primero es revisar el estado de los servicios. Probablemente alguno no haya arrancado bien.
Luego mirando los logs, se puede acotar el problema e intentar resolverlo.
Con la información que aportas esto es lo más preciso que te puedo decir.
Luego mirando los logs, se puede acotar el problema e intentar resolverlo.
Con la información que aportas esto es lo más preciso que te puedo decir.
55
Installation and Upgrades / Re: Zentyal 3.2.3, Samba hangs on 67%, doesn't continue to 100%... Any ideas???
« on: January 01, 2014, 11:19:58 am »
The problem is related to the number of files in shares.
A share with 750 large files (total 750Gb) is procesed in a few seconds.
A share with 30.000 small files (150Gb) is procesed in 2 minutes.
A share with 230.000 mixed files (420Gb) hangs at 67%
A share with 750 large files (total 750Gb) is procesed in a few seconds.
A share with 30.000 small files (150Gb) is procesed in 2 minutes.
A share with 230.000 mixed files (420Gb) hangs at 67%
56
Installation and Upgrades / Re: Zentyal 3.2.3, Samba hangs on 67%, doesn't continue to 100%... Any ideas???
« on: January 01, 2014, 08:49:30 am »
It is not a virtualization issue. I have installed zentyal 3.3.2 in 2 proliant MicroServer and same problem.
I have 3 shares with a total of 1.5Tb of mixed small and large files.
The saving changes windows is at 67% for 12h, so i think it is not running.
I have stopped the migration of 3 more servers until this issue is resolved.
This release is not ready for production because file sharing is a basic service in any environement.
I have 3 shares with a total of 1.5Tb of mixed small and large files.
The saving changes windows is at 67% for 12h, so i think it is not running.
I have stopped the migration of 3 more servers until this issue is resolved.
This release is not ready for production because file sharing is a basic service in any environement.
57
Installation and Upgrades / Re: Problem with zarafa licenses after upgrade Zentyal to 3.2.4
« on: December 30, 2013, 11:58:07 am »
In zentyal 3.0.x i have found you can disable zarafa for users Administrator and dns-host users in admin page.
Those users are no longer shown in zarafa-admin -l
In zentyal 3.3 these users are not shown in zentyal interface nor zarafa-admin -l
In default zarafa comunity, you have 3 licenses to access zarafa with zarafa connector, but one lic is used by internal user SYSTEM, so you have only 2 lic available.
Is there any way to free the license used by SYSTEM user?
Those users are no longer shown in zarafa-admin -l
In zentyal 3.3 these users are not shown in zentyal interface nor zarafa-admin -l
In default zarafa comunity, you have 3 licenses to access zarafa with zarafa connector, but one lic is used by internal user SYSTEM, so you have only 2 lic available.
Is there any way to free the license used by SYSTEM user?
58
Installation and Upgrades / Zentyal 3.3, Openchange and Zarafa questions
« on: December 21, 2013, 12:16:18 pm »
Hi, i need to reinstall my zentyal 3.0 server and i have downloaded the new 3.3 image.
I use my server for file sharing and email (Zarafa).
Acconding to my readings, the new module openchange is an alternative to zarafa trasport to connect outlook.
So i need to decide one way:
1- Zarafa and outlook connector
2- RoundCube webmail and openchange with native exchange outlook connector.
If i am right, you can not have both zarafa (for webmail and zpush) and openchange for outlook.
In case 1, i have webmail, outlook and android devices connected to mail server.
In case 2, is there any way to connect mobile devices? (android)
Is there any plan to remove zarafa and use openchange?
In my testing machine, mail stops working fews minutes after boot. RoundCube and Outlook cant connect to server.
Conectivity is restored by restarting domain and file sharing module, but drops a few minutes later.
I will reinstall the test server, but has sombody goods results with similar configuration?
I use my server for file sharing and email (Zarafa).
Acconding to my readings, the new module openchange is an alternative to zarafa trasport to connect outlook.
So i need to decide one way:
1- Zarafa and outlook connector
2- RoundCube webmail and openchange with native exchange outlook connector.
If i am right, you can not have both zarafa (for webmail and zpush) and openchange for outlook.
In case 1, i have webmail, outlook and android devices connected to mail server.
In case 2, is there any way to connect mobile devices? (android)
Is there any plan to remove zarafa and use openchange?
In my testing machine, mail stops working fews minutes after boot. RoundCube and Outlook cant connect to server.
Conectivity is restored by restarting domain and file sharing module, but drops a few minutes later.
I will reinstall the test server, but has sombody goods results with similar configuration?
59
Installation and Upgrades / Re: zentyal 3.3 as wifi router
« on: December 20, 2013, 07:28:00 pm »
Your wireless adpapter must suppont ap-mode.
use hostapd to manage the wireless link and zentyal to do the routing/firewall job.
I've done this in the past but now i use an external AP.
use hostapd to manage the wireless link and zentyal to do the routing/firewall job.
I've done this in the past but now i use an external AP.
60
Installation and Upgrades / Re: How to add network cards not detected by Zentyal
« on: November 26, 2013, 08:01:55 am »
lspci (lsusb for usb) shows you if your network card is recognized.
If so, check or modify /etc/udev/rules.d/70-persistent-net.rules for asigned intefaces names.
If so, check or modify /etc/udev/rules.d/70-persistent-net.rules for asigned intefaces names.